Multi-Scale Train Speedometer
|
Auto-Reverse Controller
|
Basic Auto-Reverse Controller
-
NOW AVAILABLE
-
Wired and tested
without power supply $69 + $7 shipping (lower 48)
-
12 volt, 1 amp
power supply add $8 + $5 additional shipping
|
Rail Car Cruise Control
-
NOW AVAILABLE
- Completed and tested
circuit ready to be installed in your engine. Please contact
dave@davebodnar.com before ordering
so that the appropriate wiring harness for the IR devices and engine slowing
resistors can be determined. $85.00 + shipping
- Complete kit of parts
including the circuit board, all resistors, capacitors, sockets, relay,
diodes, LEDs, programmed Picaxe, voltage regulator, bridge rectifier and the
other parts that are needed to make the complete circuit. You will need to
provide a suitable engine, hook up wire, solder, etc. Please contact
dave@davebodnar.com before ordering
so that the appropriate engine slowing resistors can be determined. $60.00
+ shipping
- Circuit board only.
$15.00 + shipping
- Programmed Picaxe
only. $6.00 + shipping (specify which of the programs in the article you
want on the Picaxe)
- Complete Eggliner
installation including a new Eggliner with the wired and tested circuit
installed. $125.00 + Eggliner + shipping
- Complete IR beacon,
wired and tested. $20.00 + shipping
|
Robot Train Controller
- NOW AVAILABLE
- Complete unit, wired, tested and ready to install in your engine $85 +
$7.00 shipping (lower 48)
- Contact dave@davebodnar.com for
custom installation options and costs
|
Pulsed Infrared Train Sensors
- NOW AVAILABLE
- Detect train location
without using magnets or reed switches
- The 38 KHz pulsed
infrared beam works well even in sunlight
- Sensors can be mounted to
detect IR bouncing off of a train or when a train breaks the IR beam
- Custom designs available
|
Lighthouse Beacon
Completed and tested circuit ready to be installed in your lighthouse,
airport or ???. Includes power supply. Note that some soldering will be
required with this unit if you wish to run the cable from the power supply
through the base of your lighthouse.
4 LED version with 6 or 9 volt power supply $38.00 + shipping
Halogen bulb version with 12 volt power supply $43.00 + shipping
Complete kit of parts including the circuit board, all resistors,
diodes, sockets, LEDs, programmed Picaxe, voltage regulator, and the other
parts that are needed to make the complete circuit. You will need to
provide a lighthouse, hook up wire, solder, etc.
4 LED version with 6 or 9 volt power supply $23.00 + shipping
Halogen bulb version with 12 volt power supply $28.00 + shipping
Circuit board only. $6.50 + shipping
Programmed Picaxe only. $6.00 + shipping (specify which of the programs
in the article you want on the Picaxe)
|
Morse Code Beacon
- NOW AVAILABLE
- Wired and tested
board with a user programmable microprocessor programmed with a message of
your choice (up to 127 characters)
- LED output (Red, White or Amber) - $30.00 + $2.00 shipping - all you add
is a 9 volt battery
- Incandescent bulb output (white) - $32.00 + $2.00 shipping - all you add
is an external 9-12 volt power supply
|
Capacitors & Thermistors
- 47,000 uF capacitors - $5.00 each +
shipping ($9.00 for the first one and
$1.00 each for each additional)
3 amp diodes $0.25 each - free shipping with capacitor order
-
Thermistors:
10 ohm 1.7 amps - $2.50 each -
16 ohm 2.7 amps - $2.00 each -
30 ohm 1.5 amps - $2.00 each -
Shipping for the above is $2.00 for up to 12
thermistors - another
$2.00 for 13 or more
|
Ditch Lights
- Picaxe
(programmed or not): $5.00
-
Board : $7.00
-
LEDs and other parts : $3.00
-
Kit Total : $15.00
-
Built & tested : $25.00
-
Shipping (first unit) : $5.00
-
Shipping (additional units): $1.00 each
|
Mars Lights
- Programmed PIC processor $7.00
- Circuit board
$8.00
- Complete Kit
$21.00
- Wired and tested
$40.00
|
Servo Kit
- Servo circuit board only $10.00
- Programmed Picaxe
$5.00
- Complete Kit $22.00
- Wired and tested
$34.00
|
|